BE - +32 3 820 98 60 info@vdp.com
There are no products in your shopping basket.
The easiest single-gas detector to service, with no need to take it apart to replace sensors, batteries and sensor filters. That means long life and low cost. Complete with an extensive selection of sensor options. Count on comprehensive detection, whether you’re monitoring for common or exotic hazards. The first single-gas detector with the 1-Series sensor for CO, H2S and O2. That means high accuracy, lower costs and faster sensor response time for the gases you monitor most often. Compatible with IntelliDoX. Save time and centralize data with automated bump testing, calibration and instrument management. Use IntelliDoX docking stations with Honeywell SafetySuite Device Configurator software. Alarm values HCN: 1,0-4,7ppm.
The easiest single-gas detector for Ozone to service, with no need to take it apart to replace sensors, batteries and sensor filters. That means long life and low cost. Complete with an extensive selection of sensor options. Count on comprehensive detection, whether you’re monitoring for common or exotic hazards. Compatible with IntelliDoX. Save time and centralize data with automated bump testing, calibration and instrument management. Use IntelliDoX docking stations with Honeywell SafetySuite Device Configurator software.
The easiest single-gas detector to service, with no need to take it apart to replace sensors, batteries and sensor filters. That means long life and low cost. Complete with an extensive selection of sensor options. Count on comprehensive detection, whether you’re monitoring for common or exotic hazards. The first single-gas detector with the 1-Series sensor for CO, H2S and O2. That means high accuracy, lower costs and faster sensor response time for the gases you monitor most often. Compatible with IntelliDoX. Save time and centralize data with automated bump testing, calibration and instrument management. Use IntelliDoX docking stations with Honeywell SafetySuite Device Configurator software. .
Robust belt clip for Twig NEO rotates 90 ° so that the device can be worn both vertically and horizontally. The belt clip is securely attached to the device with screws, glue and a bracket.
A simple method for measuring the time-weighted average concentrations of gas- and vapour-phase air contaminants. The monitor must b e attached to the clothing, close to the breathing zone, during the work. The contaminants are absorbed by an active carbon layer. M onitor must be analysed in a laboratory at a later time. Measurement of: ethylene oxide. Shelf life: 18 months in sealed packaging. Does not produce alarm.
New portable 4-gas detector designed specifically for sampling and monotoring confined spaces, before and after entry. The BW Ultra has enhanced sensor technology, visibility on gas readings, comfort and connectivity. It complies with all safety regulations in place by detecting your requiered gases. BW Ultra is the first gas detector on the market to feature the 1-series sensor, with fast response, reliable performance, and long life, even in extreme working conditions. Tamper-proof operation with one button operation, intuitive LCD icons for quick decision making, easy service and maintenance. Compatible with Honeywell Conected worker, Honeywell TouchConnect Technology for activating a feature, Honeywell SafetySuite for unit configuration and reporting. Quick bump <(>&<)> Calibration with IntelliDoX system. Detects simultaneously O2,LEL,H2S,CO.
The IntelliDoX system combines smart docking modules and Safety Suite software to provide automated instrument management for BW Solo gas detectors - helping you drive productivity, reliability and efficiency. Always with enabler kit (1034592)
Measuring tube to be used in combination with hand pump to measure concentration.
Measuring tube CO-HP.
Set of 2 filters to protect sensors.
The durable GasAlertMax XT provides reliable monitoring of up to four gas hazards and combines simple, one-touch operation in the field with an integrated suction pump. It is ideal for use in enclosed areas. The one-touch controls on this multi-gas detector make it exceptionally easy to use and significantly reduce the time required to train the user. The GasAlertMax XT is fully compatible with MicroDock II, the automated testing and calibration system. It incorporates vibrating and loud audiovisual alarms that continuously show the measured values. It has an integrated pump for remote sampling and is supplied with a 3 metre pump hose, 5 pump filters, a rechargeable battery and charger. It is also equipped with a sturdy clip for attaching it to clothing. It includes a two year guarantee. Version: 02. IP class 65 and Atex approved.
Testgas CO 100PPM aluminium cylinder 58L. Only for use in combination with pressure reducer.
Bottle of 110 liters with 4 test gases for calibration of 4-gas detectors. To use to calibrate manually or to combine with the Micro Dock II. Always use a shutter. Content: CH4 (2.2%), O2 (18%), H2S (25PPM) and CO (100PPM).
The GasAlertMicroClipXL is the most compact multi-gas detector for protecting against risks of flammable gas and carbon monoxide. Ideal for use in enclosed areas. This multi-gas detector can be operated with a single button providing ultimate ease of use and reduces user training time considerably. The GasAlertMicroClipXT is fully compatible with BWs MicroDock II automatic test and calibration system. With vibrating and strong audio-visual alarms that always display the measured values. Compatible with remote sampling pump (accessory). Supplied with rechargeable battery and charger. Equipped with a robust clothing clip. 2-year warranty. Sensors must be deactivated separately as required. LEL sensor is set for methane by default (specify if a different gas is applicable for the LEL sensor). Version: 02 and (NOT filtered) LEL. IP rating 65 and Atex approved.
Charging station to charge rechargable battery pack of GasalertMicro5. Colour: black.
Leather case for Twig One with transparent front and simple to use swivel belt clip mechanism to use either in vertical or in horizontal position.
Adaptor, connects USB charger to Twig One and Twig One Atex device.
Leather case for Twig One Atex with transparent front and simple to use swivel belt clip mechanism to use either in vertical or in horizontal position.
The easiest single-gas detector to service, with no need to take it apart to replace sensors, batteries and sensor filters. That means long life and low cost. Complete with an extensive selection of sensor options. Count on comprehensive detection, whether you’re monitoring for common or exotic hazards. The first single-gas detector with the 1-Series sensor for CO, H2S and O2. That means high accuracy, lower costs and faster sensor response time for the gases you monitor most often. Compatible with IntelliDoX. Save time and centralize data with automated bump testing, calibration and instrument management. Use IntelliDoX docking stations with Honeywell SafetySuite Device Configurator software.
The easiest single-gas detector to service, with no need to take it apart to replace sensors, batteries and sensor filters. That means long life and low cost. Complete with an extensive selection of sensor options. Count on comprehensive detection, whether you’re monitoring for common or exotic hazards. Compatible with IntelliDoX. Save time and centralize data with automated bump testing, calibration and instrument management. Use IntelliDoX docking stations with Honeywell SafetySuite Device Configurator software. No PPE.
To wear the E-10 on the hip.
Includes the smart-fix cover for the E-WG200 and the neck strap with double attachment. No PPE.
Float to hang at the end of a sampling hose to prevent the hose from ending up in water.
Sampling hose to attach to the hand pump or motorised pump, hose to be ordered per metre, with a maximum of 30m.
Aluminum bottle of 58 liters with test gas for calibration of Watchgas detectors. To be used for manual calibration or to be combined with the Watchgas docking station SST1/SST4 (1062077) Always to be used with the release valve 1062078. Contents: 18%O2 / 2.2% CH4 / 50 ppm CO / 10 ppm H2S in N2. Certificate included.
Charger 12-24V gas detector for Gasalertmicroclip, Quattro and MAX XT to charge in the car.
Filters to protect sensors.
Testgas Isobutylene 100PPM cylinder 58L. Only for use in combination with pressure reducer.
chemical risks.
Aluminium bottle of 34 liters with 2 test gases for calibration of gas detectors. To use to calibrate manually or to combine with the MicroDock II. Always use a shutter. Content: CH4 (2.2%), O2 (18%).
Testgas CO 100PPM aluminium cylinder 112L. Only for use in combination with pressure reducer.
Used to depressurise the bottle permanently dedicated to the destruction or recycling. Enables secure transport.
Aluminium bottle of 58 liters with 5 test gases for calibration of gas detectors. To use to calibrate manually or to combine with the MicroDock II. Always use a shutter. Content: CH4 (2,2%), O2 (18%) in N2, 25PPM H2S, 100PPM CO, CO2 (0.5%)
USB charger Twig, without adaptor for device. Not PPE.
Gas detector reusable O2 and H2S with shock resistant casing detects H2S, CO, O2 and % LEL simultaneously. Standard with built-in pump, data logging and event logging. Half-yearly calibration required. Power autonomy: Approximately 13hrs. Includes rechargeable batteries and charger. Sensors to be replaced after 2 years Sensors must be switched off. Concentration still visible on the LCD display. Registration of STEL/TWA exposure. Measurement results can be read off via USB cable. Versions with LEL sensor are calibrated for methane. Sensitivity to other explosive, hazardous substances can be set. Alarm values: O2 19.5%-23.5%. Compatible with Micro Dock II.
Replacement power adaptor for 5 GasAlert-devices.
Measuring tube to be used in combination with hand pump 1028962 to measure concentration.
UNIPHOS™ ASP-40 Air sampling pump is a one stroke pump with built-in tip breaker and shard reservoir. This ensures safe and clean working and guarantees a reliable analysis. To use with Uniphos, Kitagawa, RAE, Gastec, Kwik-draw, MSA and Dräger gas detection tubes.
Bulb and tip breaker for smoke tubes for establishing and checking air currents when checking ventilation systems, for the detection of leaks in pipelines, stoves and windows, and checking ventilation systems in mining. No PPE.
TWIG Protector is a professional security device that allows to secure personnel with one solution. Robust design and water proof sealing with neck strap. Built-in high performance GPS and telematics features allow location based services to be built to meet the requirements of the most demanding solutions. Alarm button activates a predefined emergency protocol that opearates according to DIN0825 sending latest know position via SMS while also allowing to make voice call. Version with SRD included in order to receive signals from installed beacons.
Black silicone adjustable bracelet for E-B10.
A simple method for measuring the time-weighted average concentrations of gas- and vapour-phase air contaminants. The monitor must b e attached to the clothing, close to the breathing zone, during the work. The contaminants are absorbed by an active carbon layer. M onitor must be analysed in a laboratory at a later time. Measurement of: formaldehyde. Shelf life: 18 months in sealed packaging. Do es not produce alarm.
Simultaneously monitor and display up to fi ve atmospheric hazards with the GasAlertMicro 5. Adaptable to a variety of applications, the GasAlertMicro 5 has an extensive selection of user-settable fi eld options and is available as either a standard toxic gas model, a PID model for the detection VOCs, or an IR model for CO2 detection. Use the passcode function to prevent unauthorized modifi cations of the instrument <(>&<)>#146;s settings. Compatible with BW<(>&<)>#146;s MicroDock II automatic test and calibration system, the GasAlertMicro 5 is unparalleled in its versatility, performance and overall value.
Honeywell BW™ Flex features a large, high-resolution screen on which measurements can be displayed in many different languages. Essential safety information is displayed clearly and effectively, enabling faster decisions to protect lives in hazardous conditions. The BW™ Flex uses i-series intelligent sensors. These sensors monitor sensor status in real time and enable advanced preventive calibration. These sensors also provide maintenance and end-of-life information. These advanced alerts reduce the likelihood of failure and provide you with more information on threats. Battery life of 2 months on a 4.5h charge, compatible with Intellidox. Version with Infrared LEL and O2 H2S/CO and CO2 sensor. It is not suitable for detecting hydrogen (H2) and acetylene (C2H2). Can be used in situations where no oxygen is present.
Hydrophobic filter to protect the pump of the SST4 pumped.
Male connector for connecting the pumped SST4 device to a sampling tube.
Female connector for connecting the pumped SST4 device to a sampling tube.
New portable maintainable 4-gas detector designed specifically for expert users. Expected life span : 5 years, with 3 years warranty. When there is a gas alarm, the bell icon on the display will iluminate, along wiht an indicator next to the sensor in alarm, so workers can quickly clear the area. Calibration and bump testing is still required. LEL IR sensor is always calibrated on methane, but more possibilities in other sensors . Smart sensors: data is saved on the sensor instead of on the detector. Compatible with Intellidox for Icon or nest when an other Intellidox is in use.
Neckband for gas detector Gasalertclip or GasAlert Extreme to carry on chest. Equipped with security that decouples detector if traction on the neckband.
Manual pump with 30 cm probe, without filter, gasalert microclip.
Carrying case to store and transport 4-gas gas detector Gasalertmax XT and accessories.
Charging station to charge 5 gas detectors Gasalertmax XT simultaneously.
Aluminium 34L bottle of testing gas CO 100ppm in oxygen.
Aluminium bottle of 58 liters with 2 test gases for calibration of gas detectors. To use to calibrate manually or to combine with the MicroDock II. Always use a shutter. Content: CH4 (2.2%), O2 (18%) in N2.
Testgas NH3 25PPM cylinder 34L. Only for use in combination with pressure reducer.
Testgas NO2 5PPM aluminium cylinder 34L. Only for use in combination with regulator 1015148.
Handy carrying strap for Twig around the neck. Man down alert may react differently by using this lanyard.
The GasAlertMicroClipXL is the most compact multi-gas detector for protecting against risks of flammable gas and carbon monoxide. Ideal for use in enclosed areas. This multi-gas detector can be operated with a single button providing ultimate ease of use and reduces user training time considerably. The GasAlertMicroClipXL is fully compatible with BW's MicroDock II automatic test and calibration system. With vibrating and strong audio-visual alarms that always display the measured values. Compatible with remote sampling pump (accessory). Supplied with rechargeable battery and charger. Equipped with a robust clothing clip. 2-year warranty. Sensors must be deactivated separately as required. Version: O2. IP rating 65 and Atex approved.
The GasAlertMicroClipXL is the most compact multi-gas detector for protecting against risks of flammable gas and carbon monoxide. Ideal for use in enclosed areas. This multi-gas detector can be operated with a single button providing ultimate ease of use and reduces user training time considerably. The GasAlertMicroClipXL is fully compatible with BW's MicroDock II automatic test and calibration system. With vibrating and strong audio-visual alarms that always display the measured values. Compatible with remote sampling pump (accessory). Supplied with rechargeable battery and charger. Equipped with a robust clothing clip. 2-year warranty. Sensors must be deactivated separately as required. Version: O2, H2S. IP rating 65 and Atex approved.
The IntelliDoX system combines smart docking modules and Fleet Manager II software to provide automated instrument management for BW Clip Series, GasAlertMicroClip Series and ConneX1 gas detectors - helping you drive productivity, reliability and efficiency. Always with enabler kit (1034592)
