BE - +32 3 820 98 60 info@vdp.com
There are no products in your shopping basket.
Fluid-tight glove in jersey with neoprene coating, 30.5 cm long. Provides high mechanical resistance and is resistant to a wide range of chemical products. The extra insulation layer makes the glove ideal for working for short periods with hot liquids at up to 180°C or in a cold environment up to -25°C. A popular model for the petroleum industry, for waste treatment and for the transportation and treatment of hazardous substances! Siliocne free.
Thin work glove in synthetic leather. Very breathable, with open cuff. Synthetic alternative to Tropic gloves. Sizes: 7-11.
Electrical insulating glove with mechanical resistance, which eliminates the need for wearing over-gloves. Protects against Arc Flash risks. Exterior in red, inside in black, outside has an anti-slip coating. Test voltage of 40,000 volts, operating voltage of 36,000 volts. Length 41 cm, Sizes: 7-12.
- Chemical protection - Triple PVC coating - Very finger sensitive - Seemless knitted cotton liner 13 gauge - Sizes: 8-11 - Length: 30cm - EN388:2016 4.1.2.1.X - EN ISO 374-1:2016 Type B: AJK - EN ISO 374-5:2016
Fine knitted cut-resistant glove 18 gauge made of kyorene fibers with bacteriostatic, heat-regulating and odor-neutralizing properties with a black nitrile foam coating, impact protection on the back of the hand and extra reinforcement between thumb and index finger. Without stainless steel or fiberglass.
Antistatic chemical-resistant gloves for protection against oil, paint, solvents and detergents in environments with a risk of electrostatic discharges.
Blue nitrile gloves for single use with roughened surface. Chlorinated interior for easy on and off. Reach compatible.
Defender 13 is the ultimate protection against cutting risks and is particularly well suited for the food industry. Tricot gloves without seams, that are slightly thinner than Defender 10, made with Spectra® fibres in combination with polyester and stainless steel fibres. These gloves are ambidextrous and can be worn under chain mail gloves. Defender 13 is approved for use in the food industry. Available in: white/grey. Sizes: 7 / 8 / 9 / 10, 10 cm blue cuff for better detection.
Very supple, black fireman's gloves, 100% leather with lining of interlock Kevlar® and cotton. Leather wrist protection with Velcro closure and 15 cm long cuff of supple cowsplit leather. Water repellent and heat resistant. Available in: black. Sizes: 8 / 9 / 10 / 11 / 12, length 35 cm, cuff 15 cm.
Extremely flexible glove in non-hardened vulcanised rubber. Test voltage of 10,000 volts, operating voltage of 7,500 volts. Due to its durability, insulating quality and good finger sensitivity, this glove is ideal for any environment where protection against electrocution is necessary.
60 cm cut and heat resistant arm protector. Contact heat to 100°C for max . 15 seconds. With thumb hole and Velcro closure on upper arm.
Warm, insulating gloves with acrylic/nylon liner with PVC coating. PVC-foam coating stays flexible in cold temperatures, food approved. Industy leading combination of comfort, warmth and dexterity.
Premium grain goatskin leather combined with cut and impact protection glove. TPR impact protection on top of the hand and the full lenght of the fingers. Additional palm leather layer enhances cut resistance. Reinforced seams on the index finger and base of thumb. Secure cuff closure with TPR tab closure. Sizes: 8-13.
Chemical and cut protection glove, 0,3 mm, Nitrile, sandy finish. Fully-lined, 18 gauge polyester, nylon, glass fibre thread, spandex. Oil and grease resistant, for allround work.
Flexible and close-fitting glove made of Guide HXFIBR material that offers cut protection and excellent dexterity. With nitrile coating on the palm for good grip, with high-visibility orange TPR/TPU impact protection on the back, and open fingertips for maximum flexibility.
Nitrile glove with a sand grain finish on palm for a better grip. Version without lining, so the glove is ideal for production envir onments that are sensitive to external impurities. This glove is 33 cm long and 0.38 mm thick. Food approved.
Cut-resistant glove with Zirnium with PU coating and reinforcement in split leather between thumb and index finger. Unique combination of wear-resistant leather while maintaining high finger sensitivity. Extremely good cut resistance. Sizes: 6-12.
Cut and heat resistant arm protector 45 cm., with thumb opening and velcro.Ergonomic design. Protects during 21 seconds against 100°C contact heat (test report).
Cut resistant, seemles knitted nylon-spandex-glasfibre gloves (15 gauge) with insulating layer nitrile foam/aqua PU in the palm with longer cuff. Heat resistant up to 100°C contact heat. Sizes: 6-11.
Prioritize comfort and wearer safety with the CS710 chemical resistant gloves. A double-dipped nitrile coating offers robust durability, whilst the seamless liner and natural latex-free composition ensure comfort during long periods of wear. Enhanced grip from the foamed nitrile palm coating provides extra grip, even in oily or slippery environments. Sizes: 7(S) - 11(XL).
ESD working glove seamless knitted 15gg, tight fit, with rolled knitted cuff. Touch screen compatible. PU coating on fingertips. Very comfortable. Sizes: 5-11.
Fireman's gloves in heat-resistant leather (split cow leather on the back, goat leather on the palm) and split leather hood cuff. Total length 35cm. Equipped with a waterproof, breathable and fire-resistant membrane with chemical protection. Cut resistant and water resistant. Adjustable velcro closure. Sizes: 6-12. Compliant: EN659
Extreme chemical protection: MICROCHEM™ multi-layer barrier. Utilizing unique rubber polymer and plastic laminate technology for extreme protection against a wide range of chemicals. Approved for contact heat up to 100°C/212°F, antistatic according to EN 1149-3 standards and made without natural rubber or silicone, for protection against mechanical risks and allergic reactions. Comfortable unique manufacturing process and nylon liner support for more comfort during use
Soft yet robust technical liner, engineered to offer protection against the cold and heat, as well as cut level A4/D protection Exceptional anti-wear properties and double protection against thermal hazards. Extremely durable latex coating with increased resistance around the thumb for extended use. Conform EN388:3X43D EN511: X1X EN407: X2XXXX
Very durable and super comfortable glove, seamlessly knitted in a nylon fabric with a double nitrile coating. Glove is fully coated for applications involving a lot of oil or water. The glove provides excellent grip.
Cut and heat resistant arm protector 35 cm. Conform: EN388:2016 2.X.4.X.E
Seamless glove with impermeable full nitrile coating all over the hand with extra nitrile foam coating finish on the palm for good grip on wet or oiled components. High-abrasion resistance and anti-impact protection on the back of the hand. Unique Showa ergonomic shape that replicates the natural curve of the human hand. High-visibilty green colour for visible hand signaling. Seamless knitt designed to prevent irritation.No Latex. Sizes: 7(M)-10(XXL)
Chemical resistant glove for precision and medium duty work. Double dipped in a liquid-tight NBR/PVC mix. 35 cm long safety cuff. 18gg nylon liner for high fingertip sensitivity in difficult conditions. Sizes: 7-12. Complies with: EN388:2016 4.1.3.1.X, EN407: X.1.X.X.X.X, EN ISO 374-1:2016 Type A: JKLMNOPT, EN ISO 374-5:2016 Virus.
Cut resistant and comfortable welding glove in reverse goat leather, with Kevlar lining and seams.
Synthetic glove, Nitrile foam/waterbased PU, Palm-dipped, Acrylic, Nylon, 10 gg, 15 gg, Spandex, Foam grip pattern, Fleece, Cat. II, Black, yellow, Withstands contact heat up to 100°C, for allround work . In line with : EN 388:2016, 4221A EN 407:2004, X1XXXX EN 511:2006, X2X
Extremely flexible glove in natural rubber latex. operating voltage of 500 volts, test voltage of 2.500 volts. Due to its durability, insulating quality and good finger sensitivity, this glove is ideal for any environment where protection against electrocution is necessary. length 360 mm.
Ultra-light glove 21 gauge for unparalleled comfort and dexterity with very high cut protection (F).
Cut resistant glove on seamles knit liner in renewed HXFIBRE (18 gauge) without glass fiber with nitrile coating for good grip. ESD and touch screen function, reinforcement between thumb and forefinger. Food approved. Oeko-Tex standard 100. DMF free, Silcone Free and freef of natrual latex. Sizes 6 - 12.
Glove made of cut resistant fibres on the entire glove, middle layer of chemical resistant nitrile on cotton liner. Offers protection against contact heat of 100°C during 37 seconds, and 250°C during 12 seconds. Sizes: 8,9,10.
Waterproof PVC bag with small karabiner to attach to belt. Ideal for storing and transporting electro gloves. Dimensions: 450x180x70 (mm)
Lined winter glove in goat leather. Open cuff. Thin. Fully lined. Sizes 7-11.
Durable anti-cut quality leather welding gloves in cow split leather with full seam protection and jersey lining. Kevlar stitched. Sizes: 8-9-10-11.Length cuf: 15 cm.
•Framing finger config for grasping fasteners •Padded palm with Tena-Grip™ reinforcement •Technical hex-stretch poly knit construction •Neoprene knuckle pad •Low-profile molded hook and loop closure with ID space •Pull-on tab for easy on/off •EN 388: 2016: 3.1.3.2.X •Patent pending
Seamless high cut resistant sleeve in HPPE with thumbslot and elastic cuffs on under and upperarm. Lenght 406 mm.
This glove was developed together with experts from the Dutch Defense. The target was to develop a glove that offers both a maximum protection during fast roping practices and a high tactility for handling weapons in case of interventions. Where most fast roping gloves fail to meet both conditions, we designed a unique solution in the world of fast roping. The split leather palm offers superb grip on both dry and wet ropes and is a great buffer against the heat accumulation during fast roping. On top of that, in this case handling weapons with these gloves is no longer a theme. Sizes: 7-14.
ESD working glove compatible with touch screens. Seamless nylon / carbon. Without coating. Very comfortable. Sizes: 5-11.
Fireman's gloves in heat-resistant leather (split cow leather on the back, goat leather on the palm) and para-aramid knitted cuff. Equipped with a waterproof, breathable and fire-resistant membrane with chemical protection. Cut resistant and water resistant. Adjustable velcro closure. Sizes: 6-12. Compliant: EN659
Chemical protection gloves against hazardous chemicals. Resistant to acids, bases, solvents and alcohols. Reach compatible. Length: 38cm, thickness: 0.78mm.
Glove in butyl rubber, unlined, length 35 cm, thickness 0.78mm. Colour: black. Flexible and comfortable, protects against a wide range of chemical products, detergents and solvents, liquid-tight. Silicone-free and antistatic. Sizes: 7-10. Suitable for chemical, petroleum and paint industry, transport and handling of hazardous products.
18gg liquid-tight cut protection glove with double-dipped palm; first layer of nitrile fully dipped for extra liquid barrier, second layer of nitrile palm dipped. Oeko-tex certified. Touch screen. Sizes: 7-11. Conforms to: EN388:2016 4.X.4.2.D EN407: X.1.X.X.X.X
Disposable 100% nitrile gloves with beaded cuff. Embossed fingertips for extra grip. Fully powder-free and free of natural rubber, waxes, silicones, or plasticizers. Touch N Tuff offers 3 x more puncture resistant than vinyl and natural latex. Suitable for laboratory work, chemical industry, emergency services, electronics and other precision assembly work. Colors: blue. Sizes: 6.5 to 7/7.5 to 8/8.5 to 9/9.5 to 10. Length: 300mm, thickness: 0,10mm.
Blue powder-free nitrile glove with rolled edge for applications in food industry. Completely latex free. Sizes: 6.5-7 to 9.5-10. Length: 24 cm. Thickness: 0,08mm. Package: per 100 gloves! Food approved.
Extremely flexible glove in non-hardened vulcanised rubber. Test voltage of 40,000 volts, operating voltage of 36,000 volts. Due to its durability, insulating quality and good finger sensitivity, this glove is ideal for any environment where protection against electrocution is necessary. Length 41 cm.
Glove with black HPPE and Zirnium and black PU coating and reinforcement in black split leather on palm, and fingers. Unique combination of wear-resistant leather while maintaining high finger sensitivity. Highest cut resistance. Sizes: 7-11, lenght: 25cm.
Seamless high cut resistant sleeve in HPPE with elastic cuffs on under and upperarm. Lenght 406 mm.
Extremely flexible goatskin work glove, designed for tough, hot working environments. Upper reinforced with heat resistant meta-aramide fibres and reinforced knuckles. Inner hand lined with para-aramid, which also provides cut protection level B, and reinforced externally for enhanced protection. Heat resistant double stitched seams. Sizes: 7-12.
Welding glove in cowhide split leather, with Kevlar seams. Sizes 812.
Durable unlined guide GTX synthetic leather work glove with impact protection for heavy duty work.
Cut resistant glove in special graphene fibers with double nitrile coating. These fibers provide heat regulation and keep the hands comfortable. Without glass and steel fibres.
Chemical protection glove, fully lined, 0,3* mm (*chem-layer) nitrile, fully dipped, sandy finish, 18 gg, nylon, oil and grease resistant, water and oil repellent, for allround work. Suitable for contact with foodstuffs, except for fatty foods. CAT III . In line with : EN 388:2016 4121X, EN 407:2004 X1XXXX, EN ISO 374-1:2016/Type A AJKMNOPT, EN ISO 374-5:2016/Virus .
Level F cut resistance. Protects from glass, blades and abrasions. Protection against contact heat up to 100°C. Crinkle latex grip offers excellent grip. Reinforced thumb crotch for extra protection and durability. Superior strength and comfort. Reflective label for improved visibility .Breathable seamless liner 13 gauge liner for a perfect fit. Sizes 6(XS)-11(XXL). Conform: EN388:2016 3.X.4.4.F, EN407: X.1.X.X.X.X
Liquid-tight glove in jersey with high-quality neoprene coating, 45.5 cm long. Provides high mechanical resistance and is resistant to a wide range of chemical products. Hence the great demand for this glove from the chemical and petroleum industry, the transport sector and companies that work with hazardous substances.
Composite natural latex gloves with dielectric properties coated with outer layer in polychloroprene for high mechanical resistance. No need for over-gloves. Grip motif on fingers for better grip in humid conditions. Category 3: operating voltage 26,500V, test voltage 30,000V, special properties R (acids, oil, ozone) and C (low temperatures). Supplied with 1 pair of under-gloves. Length 41 cm. Colour: orange. Available in sizes 8-11.
Goat-hide leather glove for TIG welding. Heat resistant to 100 ° C. Length of cuff: 16 cm. Sizes: 6-11.
Sleeve in polyester, nylon and glass fiber with adjustable Velcro strap system.Lenght: 475mm. Characteristics: Cuff with excellent protection against heat, cut risks and abrasion.Thermal protection upto 100°C. EN388:2.5.4.2 and EN407:X.1.X.X.X.X
Electrical insulating glove with mechanical resistance, which eliminates the need for wearing over-gloves. Protects against Arc Flash risks. Exterior in red, inside in black, outside has an anti-slip coating. Test voltage of 30,000 volts, operating voltage of 26,500 volts. Length 41 cm, Sizes: 7-12.
Knitted glove with HPPE and Zirnium with black PU coating. Extremely good cut resistance. Touch screen function on top of thumb and index. Sizes: 6-12.
Extreme comfort and protection in high cut risk applications for increased compliance and an uninterrupted workday. The Intercept™ Cut resistant Technology provides high levels of protection against lacerations. Lightest weight design for comfort and dexterity, su pporting worker use compliance. High abrasion resistance delivers longer product use life. Suitable for use across a wide range of applications and risks, avoiding the need to change gloves when transitioning between tasks. Intermittent handling of hot work items up to 100°C. Latex and Silicone free. Sizes: 6-11.
Cut and heat resistant arm protector 45 cm., with thumb opening. Ergonomic design. Protects for 21 seconds againt 100°C contact heat (test report).
Cut and heat resistant sanitized work glove compatible with touch screens
Glove with double nitrile coating on a very flexible, thin 18 gauge seamless nylon/spandex liner. The fully coated glove prevents penetration of oils (due to the red smooth nitrile coating) and this without loss of grip (due to the black nitrile foam coating). Highest protection against abrasion in combination with short-term protection against contact heat (100°C). In accordance with: EN388:2016: 4.1.2.1.A, EN407:2021: X.1.X.X.X.X.
Chemical glove for precision and medium-heavy work. Immersed in a two-layer liquid-tight Nitrile using our XLNT technology. 35 cm long safety cuff. 18gg liner for high fingertip sensitivity in difficult environments. Type A chemical protection. Food approved and Oeko-tex certified. EN388:2016 4X43C EN407: X1XXXX EN374-1:2016: AJKLMNOT
